商品説明
重要なお知らせ
ご注意(免責)> 必ずお読み下さい
●感電の恐れがありますので、活線の圧着作業は行わないで下さい。
●圧着する端子およびスリーブに適合する工具を使用して下さい。
●適正な接続を得る為、圧着する端子およびスリーブと電線のサイズを間違えないようにして下さい。圧着不良により火災の原因となる恐れがあります。
●成形確認機構により、完全に圧着できるまでハンドルは開かない。
アフターサービスについて> 交換ダイスをお求めの方へ
本体に取り付け可能な交換用ダイスを以下URLにて入手可能です。
国際規格 IEC60204-1準拠にてダイス・特注製作を行っております。ー覧に無い端子はお問合せ下さい。
↓↓
> 取扱に関してご不明がある方
販売店までお問い合わせくださいませ。
SN-28B Dupont Terminal Ratchet Crimper 2.54mm 3.96mm (AWG28-18) 0.1-1.0mm²
IWISS SN-28B Dupont terminal ratchet crimper is professional pin compression ratcheting modular insulated terminal pin tool for 2.54mm 3.96mm 28-18AWG(0.1-1.0mm²) connectors with wire-electrode cutting dies. Apply to non-insulated tabs and receptacles.
Specification
- The components of the ratchet crimping tool are made of special steel.
- Designed according to human factors engineering, it can save 50% energy when crimping.
- Precise crimping die sets and integral lock with self-releasing. Mechanism ensures high-quality crimping effect after crimping repeatedly.
- Accurate adjustment before ex works delivery.
- Due to handle grasping position, light and compact structure and handle design ensure perfect crimping effect.
Parameters | |
Capacity: | 0.1-1.0mm², for 2.54mm 3.96mm KF2510 connector |
AWG: | 28-18AWG |
Length: | 19cm / 7.5inches |
Weight: | 0.37kg / 0.8lbs |
Operation Details
- If you are right-handed, then grasp the tool in your left hand with the lettering visible and facing toward you, but upside down.
- Position the connector in one of the three bottom slots, depending on the wire gauge.
- #22 gauge works well in the center bottom slot.
- #18 gauge works well in the innermost of the bottom slots.
- The connector should be positioned so that the “wings” are facing down.
- The connector should be positioned with its back end flush with the tool and the front end of the connector facing away.
- Close the tool slightly until the ratchet just engages and grasps the connector. For heavier wire gauge (e.g. #18), you may choose to insert the wire into the connector before placing the connector into the tool.
- Use a separate wire stripper to strip about 3/16″ to 1/4″ of wire, and insert it into the connector. If you have a soft touch, you may just feel the unstripped plastic of the wire hit a stop when you insert it into the connector. In any case, don’t insert the wire too far into the connector.
- Squeeze the ratchet all the way down. It will open after this step and your connector should have successfully crimped on to the wire. The larger, outer wings should be crimped in a fold over the insulated portion of the wire, while the inner, smaller wings should be crimped over the bare wire.
If you have any doubts about the electrical quality of your crimp, you can add a tiny dab of solder to the wire-metal crimp. Not too much or the connector will not fit in the connector housing.
UPC: